Integrated Single Channel Wide Ultra2 SCSI Controller
Module (SCSI models)
Internal storage capacity of up to 72.8 GB in SCSI
Models (2 x 36.4 GB 1" SCSI Non-Hot Plug Drives)
Internal storage capacity of up to 160 GB in ATA
Models (2 x 80 GB 1" ATA/100 Non-Hot Plug Drives)
180-Watt PFC Power Supply
Front and Rear Unit Identification switches (UID)
Exceptional serviceability with optional sliding
rails, cable management and in-rack toolless service ability access
Dual Peer PCI Bus Architecture for concurrent memory
and processor access from PCI buses
Automatic Server Recovery (ASR), Compaq Insight Manager
and SmartStart
Protected by HP Services, including a three-year
parts, one- year labor, one-year, on-site service, Next Business Day
–limited, global warranty and extended, Pre-Failure Warranty which
covers processors, memory, and hard drives — Certain restrictions
and exclusions apply. Consult the Customer Support Center at 1-800-345-1518
for details.
Insight Manager 7 helps
maximize system uptime and performance and reduces the cost of maintaining
the IT infrastructure by providing proactive notification of problems
before those problems result in costly downtime and reduced productivity.
Insight Manager 7 is easy to set up and provides rapid access to detailed
fault and performance information gathered by the Management Agents.
One-click access to the Integrated Lights-Out or Remote Insight Lights
Out Edition board allows systems administrators to take full graphical
control of ProLiant servers in remote locations or lights-out data
centers. Finally, Insight Manager 7 in concert with the Version Control
Agents and Version Control Repository Manager enables systems administrators
to version manage and update system software across groups of ProLiant
servers.
SmartStart
SmartStart is a tool that
simplifies server setup, providing a rapid way to deploy reliable
and consistent server configurations. For more information, please
visit the SmartStart Web site at http://www.hp.com/servers/smartstart.
SmartStart version supported (minimum): SmartStart
5.30.
Management Agents
The Management Agents
form the foundation for HP's Intelligent Manageability strategy. They
provide direct, browser-based access to in-depth instrumentation built
into HP servers, workstations, desktops, and portables, and send alerts
to Insight Manager 7 and other enterprise management applications
in case of subsystem or environmental failures. For additional information
about the Management Agents and other management products from HP,
please visit the management Web site at http://www.hp.com/servers/manage.
ActiveUpdate
Active Update is a web-based
application that keeps IT managers directly connected to HP for proactive
notification and delivery of the latest software updates.
ROMPaq,
support software, and
configuration utilities
The latest software, drivers,
and firmware fully optimized and tested for your ProLiant server and
options.
Survey Utility and diagnostics
utilities
The most advanced configuration
analysis, reporting and troubleshooting utilities used by HP and at
your fingertips.
Optional
ProLiant Essentials Value Packs
Optional software offerings
that selectively extend the functionality of an Adaptive Infrastructure
to address specific business problems and needs:
Rapid Deployment Pack – an automated solution for multi-server deployment and provisioning, enabling companies to quickly and easily adapt to changing business demands.
Workload Management Pack – provides easier management of
complex environments, improving overall server utilization and
enabling Windows® 2000 customers for the first time to confidently
deploy multiple applications on a single multiprocessor ProLiant
Server.
Performance Management Pack – a performance management
solution that identifies and explains hardware performance bottlenecks
on ProLiant servers and attached options enabling users to better
utilize their valuable resources.
NOTE: Flexible
and volume quantity license kits are available for ProLiant Essentials Value
Packs. Refer to http://www.hp.com/servers/proliantessentials
or the various ProLiant Essentials Value Pack product QuickSpecs for more
information. NOTE: For more information regarding ProLiant Essentials Software,
please see the following URL: http://www.hp.com/servers/proliantessentials
Power-on password
Keyboard password
Diskette drive control
Diskette boot control
Network Server Mode
Removable CD-ROM/Diskette Drive Assembly
Serial interface control
Administrator's password
Disk configuration lock
Server Power Cords
North America:
One Lowline and one Highline
(IEC-IEC) power cord ships standard.
Japan:
One IEC (Highline) and one Lowline
power cord ships standard.
ROW
One Highline (IEC) power cord
ships standard
Power Supply
Auto-sensing 180-Watt PFC Power
Supply, CE Mark Compliant
System Fans
5 fans ship standard. 5 total
supported internally
Microsoft Windows NT® Server
Microsoft Windows 2000 Server
Sun Solaris Intel Platform Edition (NOTE: Sun Solaris is not currently
supported on the ProLiant DL320 ATA Models.)
Linux Red Hat, SuSE, TurboLinux Server, Caldera eServer) NOTE: For a more complete and up-to-date
listing of supported OSs and versions, please visit our OS Support Matrix
at: ftp://ftp.compaq.com/pub/products/servers/os-support-matrix-310.pdf. NOTE: For an up-to-date listing of
the latest drivers available for the HP ProLiant DL320, please see: http://www.compaq.com/support/files/server/us/index.html.
Rack Airflow Requirements
Rack 9000 and 10000 series Cabinets
The increasing power of new high-performance processor technology requires
increased cooling efficiency for rack-mounted servers. The HP 9000 Series
Rack and the new 10000 Series Rack provides enhanced airflow for maximum
cooling, allowing these racks to be fully loaded with servers using
the latest processors.
Rack 7000 series Cabinets
When installing a server with processors running at speeds of 550 MHz
or greater in HP Rack 7000 series racks with glass doors (165753-001
(42U), and 163747-001 (22U)), the new processor technology requires
the installation of HP's new High Airflow Rack Door Inserts ( 327281-B21)
(42U), 327281-B22 (42U 6 pack), or 157847-B21 (22U)) to promote enhanced
airflow for maximum cooling.
CAUTION: If
a third-party rack is used, observe the following additional requirements
to ensure adequate airflow and to prevent damage to the equipment:
Front and rear doors: If your 42U
server rack includes closing front and rear doors, you must allow
5,350 sq cm (830 square inches) of hole evenly distributed from top
to bottom to permit adequate airflow (equivalent to the required 64
percent open area for ventilation).
Side: The clearance between the
installed rack component and the side panels of the rack must be a
minimum of 7 cm (2.75 inches)
CAUTION: Always use blanking panels
to fill all remaining empty front panel U-spaces in the rack. This arrangement
ensures proper airflow. Using a rack without blanking panels results in
improper cooling that can lead to thermal damage.
NOTE: For additional
information, refer to the Setup and Installation Guide or the Documentation
CD provided with the server, or to the server documentation located in the
Support section at the following URL: http://www5.compaq.com/products/servers/ProLiantdl320/index.html
Service and Support
HP Services provides a three-year,
limited warranty, including Pre-Failure Warranty (coverage of hard drives,
memory and processors) fully supported by a worldwide network of resellers
and service providers. HP technical assistance is available 7 x 24, toll
free in the United States and Canada. Telephone support services may be
covered under warranty or available for an additional fee. NOTE: Limited
Warranty includes 3 year Parts, 1 year Labor, 1-year on-site support.
A full range of HP Care Packpackaged hardware and software services:
Installation and start up
Extended coverage hours and enhanced response times
ProLiant Essentials
Performance Management Pack v2.0, Single License
306696-B21
NOTE:
Flexible and volume quantity license kits are available for ProLiant Essentials
Value Packs. Refer to http://www.hp.com/servers/proliantessentials
or the various ProLiant Essentials Value Pack product QuickSpecs for more
information.
InterScan/Immunix Secured Solution
for HP ProLiant servers
307039-B21
NetServer to ProLiant
integrations services
HP NetServer to ProLiant
integration and assessment service
304164-002
NOTE:
HP identifies current levels of NetServer support, services, and management.
This service helps maximize customer’s ability to add ProLiant platforms
into their current environment.
HP TopTools to Insight
Manager 7 installation and startup service
304163-002
NOTE: Provides on-site
review, installation and configuration services for Insight Manager 7. HP
will also re-create, as closely as possible, the views and reports from
the customer’s current TopTools configuration. This service assures a smooth
transition to the ProLiant Essentials software.
HP NetServer to ProLiant
Essentials Rapid Deployment Pack installation and startup service
304162-002
NOTE: Install and configure
Rapid Deployment Pack in a test environment, then deploy a server image
to a maximum of 250 systems in the production environment. This service
helps to assure successful system deployment.
NOTE:
All U320 Universal Hard Drives are backward compatible to U2 or U3 speeds.
U320 drives require an optional U320 Smart Array Controller or U320 SCSI
HBA to support U320 transfer rates.
Smart Array 532 Controller NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
Smart Array 532 Controller (Japan) NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
225338-291
Compaq RAID LC2 Controller NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
Compaq RAID LC2 Controller (Japan) NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
188044-291
Smart Array 5302/128 Controller NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
Smart Array 5302/128 Controller (Japan) NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
283552-291
Smart Array 5304/256 Controller NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
Smart Array 5304/256 Controller (Japan) NOTE: Supports Wide Ultra2/3 SCSI
drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21.
283551-291
Ultra3 Channel Expansion Module for Smart Array 5300 Controller
256-MB Battery-Back Cache Module NOTE: This 256-MB Battery-Backed
Cache Module supports the Smart Array 5300 series controllers, MSA 1000
and the Smart Array Cluster Storage.
64-bit/66-MHz Single Channel Wide Ultra3 SCSI Adapter NOTE: Supports Wide Ultra3, Ultra320
SCSI drives only. If cabling to internal drives, you must first remove
the integrated controller module. ATA models require the Wide Ultra3 SCSI
cable option kit 212690-B21. NOTE: This adapter will run at 33-MHz speeds due to the 33-MHz
PCI Bus.
64-bit/66-MHz Dual Channel Wide
Ultra3 SCSI Adapter NOTE: Supports Wide Ultra3, Ultra320
SCSI drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI cable
option kit 212690-B21. NOTE: This adapter will run at 33-MHz speeds due to the 33-MHz PCI
Bus.
64-Bit/133-MHz Dual Channel Ultra320
SCSI Adapter NOTE: Supports Wide Ultra3, Ultra320
SCSI drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI cable
option kit 212690-B21. NOTE: This adapter will run at 33-MHz speeds due to the 33-MHz PCI
Bus.
64-Bit/66-MHz Dual Channel Wide
Ultra3 SCSI Adapter, Alternate OS NOTE: Supports Wide Ultra3, Ultra320
SCSI drives only. If cabling to internal drives, you must first remove the
integrated controller module. ATA models require the Wide Ultra3 SCSI cable
option kit 212690-B21. NOTE: This adapter will run at 33-MHz speeds due to the 33-MHz PCI
Bus.
NOTE: The
3U Rackmount Kit (PN 274338-B21) can support up to (2) full-height
or (4) half-height tape drives and compatible with multiple internal
Single-Ended and LVD SCSI Tape Drives including the 12/24-GB DAT,
20/40-GB DAT, 20/40-GB DAT DDS-4 8 Cassette Autoloader, AIT 35-GB
LVD, AIT 50 GB, AIT 100 GB, 20/40-GB DLT, 40/80-GB DLT, SDLT 110/220-GB,
SDLT 160/320-GB, Ultrium 230, and Ultrium 460 Tape Drives.
5U
Rackmount Kit
274339-B21
NOTE: The
5U Rackmount Kit (PN 274339-B21) can support up to (4) full-height
tape drives and is compatible with all HP internal DLT/SDLT/Ultrium
tape drives including the 20/40-GB DLT, 35/70-GB DLT, 40/80-GB DLT,
SDLT 110/220-GB, SDLT 160/320, Ultrium 230, and Ultrium 460 tape drives.
64-bit/66-MHz Fibre Channel Host Adapter NOTE: The 64-bit/66-Mhz Fibre Channel
Host Adapter has been qualified for use with the Compaq RAID Array 4000
family of products, the Enterprise Backup Solution, and the RAID Array
8000 under NetWare.
64-bit/66-MHz Fibre Channel Host Adapter (Japan) NOTE: The 64-bit/66-Mhz Fibre Channel
Host Adapter has been qualified for use with the Compaq RAID Array 4000
family of products, the Enterprise Backup Solution (EBS) offerings, and
the RAID Array 8000 under NetWare.
Rack-Mountable PDU’s – 1U/0U (Up
to 12 Outlets) NOTE: 0U mounting brackets shipped
with
the unit (separate option kit for 1U mounting).
Compaq Power Distribution Unit-16A (200-240V) (WW)
207590-B21
NOTE: The 16A
PDU also connects to the high volt models of the UPS R3000 XR (need cable
PN 340653-001 (NA)) and the UPS R6000 models. Cable PN 340653-001 required
if connecting to UPS R3000 XR ( 192186-002 NA-High Volt model only).
Compaq Power Distribution Unit-32A (200-240V) (Int’l)
207590-B31
Compaq Power Distribution Unit-40A
(200-240V) (WW)
NOTE:
This PDU has a detachable input power cord and allows for adaptability to
country specific power requirements. This model may also be used with the
high volt UPSs R3000 XR and R6000 For North America, need to order cable
PN 340653-001.
NOTE: This kit
allows you to mount the Modular PDUs in racks other than the 9000/10000
Series racks (any racks using the standard 19" rail). For more details
please refer the Modular PDU QuickSpecs.
4.5' IEC C 13 to IEC C14 PDU Jumper
Cable (1 per pack)
142257-006
4.5' IEC C 13 to IEC C14 PDU Jumper Cable (15 per pack)
142257-007
USB Options
USB Easy Access Keyboard
(Carbonite/Silver)
DC168B#
USB Easy Access Keyboard
(Carbonite) Country Key Code
NOTE: -B21 (pallet) used to ship empty
racks shipped on a truck
-B22 (shock pallet) used to ship racks with equipment installed (by custom
systems, VARs and Channels)
-B23 (crated) used for air shipments of empty racks
NOTE: It is mandatory to use a shock
pallet in order to ship racks with equipment installed. Not all Compaq
equipment is qualified to be shipped in the Rack 10000 series
NOTE: –B21 (pallet)
used to ship empty racks shipped on a truck
–B22 (shock pallet) used to ship racks with equipment installed (by custom
systems, VARs and Channels)
–B23 (crated) used for air shipments of empty racks
NOTE: This kit
can be used to connect 9000 and 10000 series racks of the same U height
together. Kit contents include hardware for connecting racks and a panel
to cover the 100-mm gap at the rear of the two racks.
Rack Blanking Panels (4U) NOTE: The Rack Blanking Panels
(PN 189453-B21) contains 10 each of (4U).
189453-B24
Rack Blanking Panels (5U) NOTE: The Rack Blanking Panels
(PN 189453-B21) contains 10 each of (5U).
189453-B25
9000/10000 Series Offset Baying Kit (42U)
248931-B21
NOTE: This kit
can be used to connect 9000 and 10000 series racks of the same U height
together. Kit contents include hardware for connecting racks and a panel
to cover the 100mm gap at the rear of the two racks.
NOTE: Input Device
Adjustable Rails (287139-B21) are for use with the TFT5110R, TFT5600RKM
and integrated keyboard/drawer which is used in mounting into third party
racks.
NOTE: Input Device
Adjustable Rails ( 287138-B21) are for use ONLY with the TFT5110R, TFT5600RKM
and integrated keyboard/drawer which is used in mounting into third party
racks.
NOTE: The Compaq
ProLiant DL320 ships with an IEC-IEC power cord used for rack mounting with
Power Distribution Units (PDUs). For stand-alone deployments or installation
without a rack, country-specific power cord options are available. U.S.
& Japan models will ship with two power cords: IEC-IEC (142257-002)
and North American C13-Nema 5-15P (103541-001) cords.
Power Cord, Euro, 10A 250 V
Straight (12 ft/3.7 m)
157215-021
Power Cord, UK, 10A 250 V Straight
(12 ft/3.7 m)
157216-031
Power Cord, Danish, 10A 250
V Straight (12 ft/3.7 m)
157218-081
Power Cord, Swiss, 10A 250 V
Straight (12 ft/3.7 m)
157219-111
Power Cord, Italian, 10A 250
V Straight (12 ft/3.7 m)
157217-061
Power Cord, South Africa, 10A
250 V Straight (12 ft/3.7 m)
157220-AR1
Service and Support Offerings (HPCare Pack Services)
Hardware Services 4-Hour On-site Service
9 x 5 Coverage, 3 Years
(6-3 Part Number for U.S.)
162676-002
9 x 5 Coverage, 3 Years
(6-3 Part Number for EMEA)
324416-022
24 x 7 Coverage, 3 Years
(6-3 Part Number for U.S.)
162675-002
24 x 7 Coverage, 3 Years
(6-3 Part Number for EMEA)
376910-022
Hardware Services Next Business Day On-Site Service
9 x 5 Next Business Day
Coverage, 3 Years (6-3 Part Number for U.S.)
102407-002
9 x 5 Next Business Day
Coverage, 3 Years (6-3 Part Number for EMEA)
206947-022
Installation
& Start-up Services
Hardware Installation (6-3
Part Number for US)
401791-002
Server Installation and
Set-Up (Installation of the server, installation of the appropriate
service tools, check to ensure device SW and firmware is loaded and
installation of the operating system software (6-3 Part Number for
EMEA)
204563-022
Pre-installation planning;
unpack equipment, install most current Compaq HW options internal
to server at same time of server installation; assemble & test;
basic user information provided; Install & configure basic functionality
of Win NT Operating System plus up to 1 day start-up activity, configure
print & network access services, and orientation (6-3 Part Number
for U.S.)
240013-002
Pre-installation planning;
unpack equipment, install most current Compaq HW options internal
to server at same time of server installation; assemble & test;
basic user information provided; Install & configure basic functionality
of NovellÒ NetWare Operating System plus up to 1 day start-up
activity, configure print & network access services, and orientation
(6-3 Part Number for U.S.)
240008-002
HP Care Pack
Priority Services for ProLiant Servers – Priority Level
9 x 5 HW, 4-hr response, Next Available HW engineer; 9 x 5 Bronze
Software Support 2-hr response for Windows NT, Windows 2000, Professional,
Server or Advanced Server Operating System, Next Available Specialist
(6-3 Part Number for U.S.)
239928-002
9 x 5 HW, 4-hr response,
Next Available HW engineer; 9 x 5 Bronze Software Support 2-hr response
for Novell NetWare Operating System, Next Available Specialist (6-3
Part Number for U.S.)
239968-002
9 x 5 4-hour H/W, 5 x 9 2-hour O/S (NT & NetWare), Three Years
(6-3 Part Number for EMEA)
179834-022
HP Care Pack
Priority Services for ProLiant Servers – Priority 24 Level
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Bronze Software Support,
2-hr response for Windows NT, Windows 2000, Professional, Server or
Advanced Server Operating System, Next Available Specialist (6-3 Part
Number for U.S.)
239930-002
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Bronze Software Support,
2-hr response for Novell NetWare Operating System, Next Available
Specialist (6-3 Part Number for U.S.)
239970-002
7 x 24 4-hour H/W, 7 x
24 2-hour O/S (NT & NetWare), Three years (6-3 Part Number for
EMEA)
179839-022
CarePaq Priority Services for ProLiant Servers
– Priority Silver
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Software Support,
1-hr response, Monday – Friday, 8AM – 5PM local time, 2-hr
response after hours for Windows NT, Windows 2000, Professional, Server
or Advanced Server Operating System, Technical Account Manager, Technical
Newsletter, SW activity review, proactive patch notification, 1 System
Healthcheck per year (6-3 Part Number for U.S.)
239932-002
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Subsequent System Support for Windows
NT, Windows 2000, Professional, Server or Advanced Server Operating
System (6-3 Part Number for U.S.)
239934-002
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Software Support,
1-hr response, Monday – Friday, 8AM – 5PM local time, 2-hr
response after hours for Novell NetWare Operating System, Technical
Account Manager, Technical Newsletter, SW activity review (6-3 Part
Number for U.S.)
239972-002
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Subsequent System Support for Novell
NetWare Operating System (6-3 Part Number for U.S.)
239974-002
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Software Support,
1-hr response, Monday – Friday, 8AM – 5PM local time, 2-hr
response after hours for Windows NT, Windows 2000, Professional, Server
or Advanced Server Operating System, Technical Account Manager, Technical
Newsletter, SW activity review, proactive patch notification, 1 System
Healthcheck per year (2-5-2 Part Number for Canada)
FM-M04E1-36
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Subsequent System Support for Windows
NT, Windows 2000, Professional, Server or Advanced Server Operating
System (2-5-2 Part Number for Canada)
FM-M24E1-36
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Software Support,
1-hr response, Monday – Friday, 8AM – 5PM local time, 2-hr
response after hours for Novell NetWare Operating System, Technical
Account Manager, Technical Newsletter, SW activity review (2-5-2 Part
Number for Canada)
FM-N04E1-36
24 x 7 HW, 4-hr response,
Named HW engineer; 24 x 7 Silver Subsequent System Support for Novell
NetWare Operating System (2-5-2 Part Number for Canada)
128-MB PC 133-MHz Registered ECC SDRAM DIMM installed
(1 x 128-MB SDRAM DIMM)
Standard Memory Plus Optional Memory
Up to 1664-MB memory is available with the optional
installation of PC 133-MHz Registered ECC SDRAM DIMM memory kits.
Standard Memory Replaced with Optional Memory
Up to 2048-MB of memory is available with the removal
of the standard 128-MB of memory and the optional installation of PC133-MHz
Registered ECC SDRAM DIMM memory kits. NOTE: Chart does not represent
all possible configurations.
Memory
Slot
1
2
3
4
Standard
128 MB
128 MB
Empty
Empty
Empty
Optional
1664 MB
128 MB
512 MB
512 MB
512 MB
Maximum
2048 MB
512 MB
512 MB
512 MB
512 MB
Following are memory options available from Compaq:
NOTE:
All U320 Universal Hard Drives are backward compatible to U2 or U3 speeds.
U320 drives require an optional U320 Smart Array Controller or U320 SCSI
HBA to support U320 transfer rates.
Canadian Site
DL QuickSpecs
Search:
US QuickSpecs 
327281-B21
© 2013 USA PartsDirect