Standard
height/full-height PCI Express x16/PCI-X riser board
9.
Optional
3rd and 4th 3.5” Non-Hot plug SATA or hot plug SAS/SATA
hard drive bays
10.
Standard
1st and 2nd 3.5” Non-Hot plug SATA or hot plug SAS/SATA
hard drive bays
11.
Expansion
Slots: Non-Hot Plug Models Two available x16 PCI-Express Gen2 slots
Hot Plug Models One available x16 PCI-Express slot Gen2 slot
What's
New
Support for SATA Hot Plug 3.5" Midline (MDL) Solid State Drives
Support for SAS Hot Plug 3.5" Enterprise (ENT) Hard Drives
At
A Glance
The HP ProLiant DL160 G5 server is an affordable
1U, dual processor capable server equipped with essential performance features
that provide customers with a platform to design a fully optimized solution.
It is ideal for general purpose and high performance computing.
Processors:
Supports up to two Intel® Quad-Core 5400 or Dual-Core 5200
sequence processors
Supports up to 64 GB of PC2-5300 (DDR2-667) and up to 32 GB of
PC2-6400 (DDR2-800) fully buffered DIMMs (DDR2-667) with Advanced
ECC
Internal Drive Support:
Support for up to four 3.5" Non-Hot plug serial ATA (SATA)
hard drives or;
Support for up to four 3.5" Hot plug Serial Attached SCSI
(SAS) or SATA hard drives.
NOTE: Installation of the Hot
Plug Backplane 1U 2S Kit (445985-B21) is required if ordering third
or fourth Hard Drives for Hot Plug models only.
Internal storage capacity of up to 1.0TB (4 x 1TB Hot Plug 3.5"
SATA), 3.0TB (4 x 750 Non-Hot Plug SATA) or 4.0TB (4 x 1TB Hot Plug
3.5" SAS)
Network Controller:
Two embedded NC105i PCIe Gigabit Server Adapters
Storage Controllers:
Non-Hot Plug SATA Models: HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5
Gb/s SATA
Hot Plug SAS/SATA Models: HP SC40Ge 4-Port Internal SAS HBA with
RAID 0, 1 NOTE: When using the SC40Ge
with SATA Hard Drives, 1.5G SATA Hard Drives are required. NOTE: Transfer rate: 1.5 Gb/s SATA, 3Gb/s SAS
Expansion Slots:
Non-Hot Plug Models: Two available PCI Express 2.0 slots:
Slot 2: low-profile/half-height PCI-X slot populated by the
SAS/SATA storage controller
Infrastructure Management:
HP Lights Out 100i Advanced Remote Management with new licensed
key activated upgrades for Virtual KVM and virtual media support.
LO100i management support for the DL160 G5 includes:
IPMI 2.0 & SMASH CLP support
ROM Setup Utility
Improvements to virtual media with the addition of USB 2.0 drives
and protocol support for much faster transfer speeds and DVD-ROM
support plus simplified virtual media (floppy and CD with no FTTP
server requirements)
Enhanced browser interface and embedded KVM over IP provides OS-independent
remote graphical console
USB Ports:
Five USB ports (two front, one internal, two rear)
Optical Drive:
Support for one (optional): DVD-ROM, DVD/CD RW
Power Supply:
650W Power Supply (Non-Hot Plug, Autoswitching)
Optional high-efficiency model
NOTE: Optional high-efficiency
model requires the purchase of HP Power Supply Backplane (453652-B21)
Additional Features:
Support for:
NVIDIA Quadro FX3700 512MB PCIe x 16 graphics card
NVIDIA Quadro FX1700 512MB PCIe x 16 graphics card
Form Factor:
Rack (1U)
Fixed mounting rails included with all models
Deployment/Serviceability:
Tool-less access to all system components for easy in rack serviceability
Customer Self Repair (CSR): HP products are designed with many
CSR parts to minimize repair time and allow for greater flexibility
in performing defective parts replacement
Warranty:
This product is covered by a global limited warranty and supported
by HP Services and a worldwide network of HP Authorized Channel Partners.
Hardware diagnostic support and repair is available for one year from
date of purchase. Support for software and initial setup is available
for 90 days from date of purchase. Enhancements to warranty services
are available through HP Care Pack services or customized service
agreements. Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details. NOTE: Server Warranty includes
1 year Parts, 1 year Labor, 1-year on-site support with next business
day response. Warranty repairs may be accomplished through the use
of Customer Self Repair (CSR) parts. These parts fall into two categories:
1) Mandatory CSR parts are designed for easy replacement. A travel
and labor charge will result when customers decline to replace a Mandatory
CSR part; 2) Optional CSR parts are also designed for easy replacement
but may involve added complexity. Customers may choose to have HP
replace Optional CSR parts at no charge. Additional information regarding
worldwide limited warranty and technical support is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html.
NOTE: For a brief, printer friendly data sheet
that describes this product and informs you of the essential capabilities and
specifications, please visit: http://h71028.www7.hp.com/ERC/downloads/4AA1-6954ENW.pdf NOTE:
For the Standard Features shipped in the Factory Integrated Models, please see
the "Configuration Information - Factory Integrated Models" section.
Processor One of the following depending on Model
Quad-Core
Intel® Xeon® processor X5482 (3.20 GHz, 120W, 1600MHz FSB) NOTE:
Available through Configure To Order only. See Factory Integration Models section
for more details.
Quad-Core
Intel® Xeon® processor X5470 (3.33 GHz, 120W, 1333MHz FSB) NOTE:
Available through Configure To Order only. See Factory Integration Models section
for more details.
Quad-Core
Intel® Xeon® processor X5460 (3.16 GHz, 120W, 1333MHz FSB) NOTE:
Available through Configure To Order only. See Factory Integration Models section
for more details.
Quad-Core
Intel® Xeon® processor L5430 (2.60 GHz, 50W, 1333MHz FSB) NOTE:
Available through Configure To Order only. See Factory Integration Models section
for more details.
Dual-Core Intel® Xeon® processor
L5240 (3.00 GHz, 40W, TDP, 1333MHz FSB) NOTE:
Available through Configure To Order only. See Factory Integration Models section
for more details.
Upgradeability
Upgradeable to two processors
Chipset
Intel®
5400 Chipset
Cache
Memory
12 MB (2 x 6 MB) Level
2 cache (5400 sequence)
6
MB (1 x 6 MB) Level 2 cache (5200 sequence)
Memory Protection
Advanced ECC capabilities
DL160 G5 Memory
Type
PC2-5300 (DDR2-667)
and PC2-6400 (DDR2-800)
Standard
1 GB
(2 x 512 MB)
Maximum
32 GB
64 GB
(8 x 4 GB) PC2-6400
(8 x 8 GB)
Network
Controller
Two embedded NC105i PCIe Gigabit
Server Adapters
Expansion Slots #
Technology
Bus Width
Connector Width*
Bus Number*
Device No.**
Form Factor
Notes
1
PCI-Express 2.0
x16
x16
1
0
Full length, full height
3.3 volts
1
PCI-X***
64-bit
N/A
5
1
Full length, full height
3.3 volts
2
PCI-Express 2.0
x16
x16
6
3
Low Profile
3.3 volts
2
PCI-X***
64-bit
N/A
5
1
Low Profile
3.3 volts
NOTE: All slots can accept
universal keyed PCI cards
* Default bus assignment. Inserting
cards with PCI bridges may alter the actual bus assignment number.
** Slots are enumerated differently
based on OS. MS OS's enumerate from lowest to highest Device ID by bus (starting
with the lowest bus).
*** PCI-X bus speed will be 133MHz
when only one PCI-X card is installed. It will be 100MHz when both slots
have PCI-X cards installed.
Storage Controller
Non-Hot Plug SATA Models
HP Embedded SATA RAID Controller
(integrated into the south-bridge) supporting SW RAID 0,1 NOTE: Transfer rate: 1.5 Gb/s SATA
Hot Plug SATA/SAS Models
HP SC40Ge HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. NOTE: Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS
NOTE:
A diskette drive, USB floppy drive key or virtual FDD using LO100 Advanced
Pack is needed to install storage controller drivers during a Windows operating
system installation from a CD.
Storage
Diskette Drives
Via USB only
Optical Drives
Optional 8x IDE (ATAPI) DVD-ROM
drive, slim
Optional 24x IDE (ATAPI) CD-ROM
drive (optional)
Drive Bays
Up to 4 Non-hot plug SATA 3.5"
drives
Up to 4 Hot plug SAS/SATA 3.5"
drives
Maximum
Internal Storage
Non-Hot Plug SATA
3.0TB
4 x 750GB
Hot Plug SATA
4.0TB
4 x 1TB
Hot Plug SAS
4.0TB
4 x 1TB
Interfaces
Parallel
None
Network RJ-45(Ethernet)
2 10/100/1000 NIC ports (plus
1 dedicated for the HP ProLiant Lights Out 100i Remote Management)
HP Lights-Out 100i Remote Management delivers affordable, entry level
remote management capabilities for HP ProLiant 100 Series servers with
embedded LO100i. It allows customers or their service providers to remotely
manage ProLiant 100 Series servers remotely over a LAN or the Internet
and consists of the following:
LO100i Standard is embedded remote management and provides basic remote
control via telnet, browser, and IPMI 2.0 and SMASH
LO100i Advanced Pack License are upgrades for essential, secure, remote
control, serial console, virtual media, and Virtual KVM (graphical hardware-based,
remote console)
NOTE: Flexible and volume quantity (AKA)
license kits are available for the Lights-Out 100i Lights-Out 100 Advanced
Pack licenses as well as Electronic License To Use (E-LTU). AKA Tracking
licenses require a 100 unit minimum forecast at initial contract signing.
For these additional part numbers, please refer to each software products.
QuickSpecs at this link for more information: www.hp.com/go/lo100.
Industry Standard
Compliance
ACPI V2.0 Compliant
PCI 2.2 Compliant
PXE Support
WOL Support
Microsoft® Logo certifications
IPMI 2.0, SMASH CLP compliant
Manageability
HP Lights-Out 100i Standard provides the following OS-independent remote
control capabilities:
Virtual power
System event log access
System health
Remote serial console (serial redirection)
Browser, Telnet access
SMASH-CLP compliant
IPMI 2.0 compliant
HP Lights-Out 100i Advanced Pack provides license key activated upgrades
to the following:
Virtual KVM (KVM over IP functionality embedded on the system board)
Security
Power-on password
Setup password
Server
Power Cords
One 6' Highline
(IEC-IEC) power cord ships standard NOTE:
HP ProLiant DL servers no longer ship standard with NEMA power cords (163719-002)
that allow connection to 110V wall outlets in a home or office. ProLiant DL servers
are primarily connected to PDU's in data center racks so they now ship standard
with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant
DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001)
must be ordered separately.
If customers require a local power
cord, they can check the power cord matrix for the appropriate cord. Please see
the following power cord matrix: http://www.hp.com/go/powercordmatrix.
UPS and PDU Power
Cord Matrix
Please see the UPS and PDU cable
matrix's on the HP Power Protection and Management page. Under Power Cords,
click on the "HP Power Cord Matrix" link. That link will list
cable descriptions, requirements, and specifications for UPS and PDU units.
Please see the following link: www.hp.com/products/powercords.
NOTE: For more information on HP's
Certified and Supported ProLiant Servers for OS and Virtualization Software
and latest listing of software drivers available for your server, please
visit our Support Matrix at: http://www.hp.com/go/supportos
and our driver download page http://www.hp.com/support/DL160G5.
Rack
Airflow Requirements
Rack 10000 G2 series Cabinets
The increasing power of new high-performance processor technology requires
increased cooling efficiency for rack-mounted servers. The 10000 G2 Series
Racks provide enhanced airflow for maximum cooling, allowing these racks
to be fully loaded with servers using the latest processors.
CAUTION:
If a third-party rack is used, observe the following additional requirements to
ensure adequate airflow and to prevent damage to the equipment:
Front and rear doors: If your 42U server rack includes closing front and rear
doors, you must allow 5,350 sq cm (830 square inches) of hole evenly distributed
from top to bottom to permit adequate airflow (equivalent to the required 64 percent
open area for ventilation). Side: The clearance between the installed rack
component and the side panels of the rack must be a minimum of 7 cm (2.75 inches)
CAUTION: Always use blanking
panels to fill all remaining empty front panel U-spaces in the rack. This arrangement
ensures proper airflow. Using a rack without blanking panels results in improper
cooling that can lead to thermal damage.
NOTE: For additional
information, refer to the Setup and Installation Guide or the Documentation
CD provided with the server, or to the server documentation located in the
Support section at the following URL: www.hp.com/servers/dl160.
Rack Support
The DL Fixed Rail System supports
installation in racks with square or round mounting holes (including Compaq/HP
7000, 9000, 10000 and HP series), with an adjustment range of 24" -
36".
Telco Rack Support
Installation into Telco 2 post, and 4 post, or threaded holes racks requires
a 3rd party option kit. For additional information, please visit: www.racksolutions.com.
Factory Express Portfolio for
Servers and Storage
HP Factory Express offers configuration,
customization, integration and deployment services for HP servers and storage
products. Customers can choose how their factory solutions are built, tested,
integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as individual
factory services, such as image loading, asset tagging, and custom packaging.
HP products supported through Factory Express include a wide array of servers
and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem,
HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries
and configurable network switches.
For more information on Factory Express services for your specific server
model please contact your sales representative or go to: http://www.hp.com/go/factory-express.
HP Enterprise Configurator
The HP eConfigure Enterprise Configurator now provides factory default
racking for our HP hardware portfolio. This approach is aligned with our
strategic direction to meet the needs and expectations of our valued customers.
If you require "custom" rack configuration, please contact HP's
Customer Business Center or an Authorized Partner for assistance.
Service and Support
HP Care Pack Services provide total care and support expertise with committed
response designed to meet your IT and business needs.
HP Care Pack Services provide total care and support expertise with committed
response designed to meet your IT and business needs.
HP Care Pack services include coverage for the HP branded hardware options
qualified for the server that are purchased at the same time or afterward
and internal to the enclosure. It also includes the 22" and smaller
external monitors and tower UPS options up to 3kVA. These items will be
covered at the same service level and for the same coverage period as
the server. Coverage of UPS Battery is not included and standard warranty
terms & conditions apply. For servers or storage systems installed
within a rack, service also covers all HP qualified rack options installed
within the same rack.
To fully capitalize on your HP ProLiant servers' capabilities requires
a service partner who thoroughly understands your server technology and
systems environment. HP Services, an industry leader in provision of multi
vender support solutions provides a range of support services designed
to meet the varying needs of business. Whether an SMB or large global
corporation HP has a ProLiant server support offer to help you speedily
deploy and maximize system uptime.
Recommended Service Simplify ProLiant solution implementation,
maintenance and management.
Support Service 3 Year, 9x5 Next Business Day coverage,
excluding HP holidays only
Deployment Service Hardware Installation only
Enhanced Service Optimize service level to increase IT
performance and availability
Support Service 3 Year 13x5 Same Business Day, 4-Hour
response coverage
Deployment Service Installation and Start-up only
Installation & Start-Up of a ProLiant server and Microsoft or Linux O/S per the Customer Description and/or Data Sheet. To be delivered on a scheduled basis 8am-5pm, M-F, excl. HP holidays.
NOTE:
High Performance Computing (HPC) interconnect technologies are available
for the DL160 G5 under the Cluster Platform product portfolio. These high-speed
interconnects are fully supported by HP when they are part of these configure
to order clusters. Solutions can be defined with a lot of flexibility with
the help of configuration tools. Please visit the following URL to configure
HPC Clusters with InfiniBand, Gigabit Ethernet or Myrinet Interconnects:
http://www.hp.com/techservers/clusters/ucp/index.html
Non-Hot Plug Serial
ATA (SATA) Models NOTE: Non-Hot Plug models are not
upgradeable to Hot Plug. Non-Hot Plug models require the addition of the
HP HBA SAS-SATA 4x1LN Cable Kit (P/N: 452130-B21) in order to connect a
hardware RAID controller.
HP DL160 G5 X5472 Non-Hot Plug SATA, 2GB, (1P)
445198-001
HP
DL160 G5 E5430 Non-Hot Plug SATA, 1GB, (1P) 445197-001
HP DL160
G5 E5405 Non-Hot Plug SATA, 1GB, (1P) 445196-001
Processor(s) One of the following depending on model
The ProLiant
Smart Buy program offers a collection of promotional server and option products
that are configured with SMB in mind, offered at discounted prices, and
positioned for quick delivery. Smart Buy server offers are available for
a limited time only.
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure
a Factory Integrated Model. To ensure only valid configurations are ordered,
HP recommends the use of an HP approved configurator. Contact your local
sales representative for additional information. NOTE: HP does not allow factory integration of options into standard
models listed above. Configure-to-order servers must start with a CTO
Chassis.. NOTE: FIO indicates that this option is a Factory Installable Option.
Step
1: Base Configuration (choose one of the following configurable models)
Non-Hot Plug SATA Model NOTE: Non-Hot Plug models are not
upgradeable to Hot Plug. Non-Hot Plug models require the addition of the
HP HBA SAS-SATA 4x1LN Cable Kit (P/N: 452130-B21) in order to connect a
hardware RAID controller.
HP ProLiant DL160 G5 Non-Hot Plug
SATA Rack CTO Chassis
445192-B21
Factory Integrated
Model ships with:
Two embedded NC105i PCIe Gigabit
Server Adapters (WOL & PXE-capable)
Hard Drive NOTE: SATA Non-Hot Plug Hard Drives
ONLY required when Non-Hot Plug CTO Chassis Model in selected in Step 1.
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and
the server backplane) should operate at the same data transfer rate or the
system bandwidth will be negotiated down to an acceptable level for all
components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
NOTE: A minimum
of one hard drive is required when purchasing Non-Hot Plug CTO Chassis Model
(P/N 445192-B21).
Serial-ATA (SATA) Non-Hot Plug
Hard Drives (Non-Hot Plug Models Only)
Storage
Controllers NOTE: SAS Controller ONLY required
when Hot- Plug CTO Chassis Model is selected in Step 1.
HP SC44Ge Host Bus Adapter NOTE: When using the SC44Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS.
HP SC40Ge 4 Internal PCIe SAS
RAID Half Height HBA, FIO NOTE: Recommended HBA when purchasing
Hot Plug CTO Chassis Model (P/N 445193-B21). NOTE: When using the SC40Ge with SATA Hard Drives, 1.5G SATA Hard
Drives are required. Transfer rate 1.5 Gb/s SATA, 3 Gb/s SAS.
HP Smart Array E500/256MB Controller
with Battery, FIO NOTE: Customers can only order one
Smart Array E500/256MB Controller and one Battery-backed write cache upgrade
(P/N 383280-B21) for the HP ProLiant DL160 G5 server based on battery space.
462105-B21
Battery-backed write cache upgrade NOTE: When installing a battery-backed
write cache module, the HP Smart Array E500 must be installed in the full-length
PCI slot. This 256MB Battery-backed write cache upgrade for RAID 5 support.
NOTE: This option
is required for any internal port HBA or controller that has a standard
4 port SAS/SATA connector.
Step 3: Choose Additional Factory
Integratable Options (only one of the following from each list unless otherwise
noted)
Power Supply
HP 1200W High Efficiency Power
Supply Kit, FIO NOTE: Selection of the HE Power Supply
Unit will remove the 650 Watt standard power supply and requires the purchase
of Power Supply Backplane (p/n 453652-B21).
453650-B21
HP Power Supply Backplane, FIO NOTE: This backplane must be ordered
with the High Efficiency Power Supply (P/N 453650-B2).
453652-B21
Step 4: Choose Additional Options
for Factory Integration
NOTE: For additional
options, please refer to the "Core Options" and "Additional
Options" section below.
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and
the server backplane) should operate at the same data transfer rate or the
system bandwidth will be negotiated down to an acceptable level for all
components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
HP NC522SFP Dual Port 10GbE Server
Adapter NOTE: A minimum of two Gigabytes
(2 GB) of server memory is required per each NC522SFP adapter. NOTE: Direct Attach Cable (DAC) for copper environments or fiber
transceivers and cables for fiber-optic environments must be purchased separately.
HP LO100i Advanced Pack, No Media
1-Server License including 1 year of 24x7 Technical Support and Updates
530521-B21
NOTE: Flexible
and volume quantity (AKA) license kits are available for the Lights-Out
100i Advanced Pack licenses as well as Electronic License To Use (E-LTU).
AKA Tracking licenses require a 100 unit minimum forecast at initial contract
signing. For these additional part numbers, please refer to each software
products' QuickSpecs at this link for more information: www.hp.com/go/lo100
HP Insight Software
HP Insight Rapid Deployment software
HP Insight Rapid Deployment software
No Media 1-Server License including 1 year of 24x7 Technical Support and
Updates NOTE: This license allows 1 server
to be deployed. Customer will receive a printed license entitlement certificate
via physical shipment. The license entitlement certificate must be redeemed
online or via fax in order to obtain the license activation key(s). Includes
one year of 24 x 7 HP Software Technical Support Service.
NOTE:
Installation of the Hot Plug Backplane 1U 2S Kit (445985-B21) is required
if ordering third or fourth Hard Drives for Hot Plug models only.
Storage Controllers
NOTE: The addition
of storage controllers for internal hard drive use is intended for use ONLY
with the Hot Plug SATA/SAS Model Chassis (P/N 445193-B21).
HP Smart Array E500/256MB Controller
NOTE: Standard RAID 0,1, 1+0. NOTE: Customers can only order one Smart Array E500/256MB Controller
and one Battery-backed write cache upgrade (P/N 383280-B21) for the HP ProLiant
DL160 G5 server based on battery space.
HP Smart Array P400/256 Controller NOTE: Customers can only order one
Smart Array P400/256MB Controller and one Battery-backed write cache upgrade
(P/N 383280-B21) for the HP ProLiant DL160 G5 server based on battery space.
HP Smart Array P400/512 Controller
with BBWC NOTE: Customers can only order one
Smart Array P400/512MB BBWC Controllers for the HP ProLiant DL160 G5 server
based on battery space.
Battery-backed write cache upgrade NOTE: When installing a battery-backed
write cache module, the HP Smart Array E500 must be installed in the full-length
PCI slot. This 256MB Battery-backed write cache upgrade for RAID 5 support.
HP 8 Internal Port SAS HBA with
RAID NOTE: For use with Hot Plug SAS/SATA
models. NOTE: The selection HP 8 Internal Port SAS HBA with RAID requires
the purchase of the LowProfile PCI-X Riser Option kit (P/N 452698-B21) NOTE: Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS.
HP SC44Ge Host Bus Adapter NOTE: PCI-Express SAS HBA. NOTE: When using the SC44Ge with SATA Hard Drives, 1.5G SATA Hard
Drives are required. Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS.
HP StorageWorks 1U USB Rack-Mount
Kit with one DAT 160 USB Tape Drive NOTE: Pre-configured with one DAT
160 USB tape drive.
AG703A
SAS Rack-Mount
Tape Drives NOTE: HP recommends purchasing the
HP SC44Ge HBA ( 416096-B21) for a dedicated SAS HBA for tape.
HP StorageWorks 1U SAS Rack-Mount
Kit with one LTO-4 Ultrium 1760 NOTE: Pre-configured with one LTO-4
Ultrium 1760 SAS tape drive.
EH946A
HP StorageWorks 1U SAS Rack-Mount
Kit NOTE: Supports up to (2) half-height
SAS tape drives.
AE459A
HP StorageWorks DAT 160 SAS Internal
Tape Drive NOTE: Mounts inside the 1U SAS Rack-Mount
Kit (AE459A)
Q1587A
HP StorageWorks LTO-2 Ultrium
448 SAS Internal Tape Drive NOTE: Mounts inside the 1U SAS Rack-Mount
Kit (AE459A)
DW085A
HP StorageWorks LTO-3 Ultrium
920 SAS Internal Tape Drive NOTE: Mounts inside the 1U SAS Rack-Mount
Kit (AE459A)
EH847A
SCSI Rack-Mount
Tape Solutions NOTE: SCSI Controller required. HP
recommends purchasing the HP SC11Xe HBA ( 412911-B21) for a dedicated SCSI
HBA for tape.
HP StorageWorks 1U SCSI Rack-mount
kit with one LTO-2 Ultrium 448 SCSI Tape Drive (Carbonite) NOTE: Pre-configured with one LTO-2
Ultrium 448 SCSI tape drive.
DW028B
HP StorageWorks 1U SCSI Rack-mount
kit with one LTO-3 Ultrium 920 NOTE: Pre-configured with one LTO-3
Ultrium 920 SCSI tape drive.
EH903A
HP StorageWorks 3U SCSI Rack-Mount
with 1 LTO-4 Ultrium 1840 Tape Drive NOTE: Pre-configured with one LTO-4
Ultrium 1840 SCSI tape drive.
EH926A
For an up-to-date listing
of the latest O/S and software support details for HP Ultrium tape drives,
please visit: http://www.hp.com/go/connect
Tape Autoloaders
HP StorageWorks DAT Autoloader
HP StorageWorks DAT 72x10 tape
autoloader
AE313B
HP StorageWorks 1/8 G2 Tape Autoloader
HP StorageWorks 1/8 G2 LTO-4 Ultrium
1760 SAS Tape Autoloader
AK377A
HP StorageWorks 1/8 G2 LTO-3 Ultrium
920 SAS Autoloader
AH558A
HP StorageWorks 1/8 G2 LTO-2 Ultrium
448 Tape Autoloader
AH164A
HP StorageWorks 1/8 G2 Tape Autoloader
Rack Kit NOTE: Required to install the 1/8
G2 Autoloaders in a standard 19-inch rack; includes rails and rackmount
instructions.
AH166A
NOTE: Please see
the QuickSpecs for Technical Specifications and additional information:
http://www.hp.com/go/automation
needed to create a complete solution; reference current compatibility information
at: http://www.hp.com/go/ebs.
Tape Libraries
HP StorageWorks MSL2024 Tape Library
HP StorageWorks MSL2024 1 LTO-4
Ultrium 1840 SCSI Drive Library
AJ033A
HP StorageWorks MSL2024 1 LTO-4
Ultrium 1760 SAS Drive Library
AK378A
HP StorageWorks MSL2024 1 LTO-3
Ultrium 960 SCSI Drive Library
HP StorageWorks MSL4048 1 Ultrium
920 SAS Drive Library
AH560A
HP StorageWorks MSL4048 1 Ultrium
960 SCSI Drive Library
AG322A
HP StorageWorks MSL4048 2 LTO-4
Ultrium 1760 SAS Drive Library
AK380A
HP StorageWorks MSL4048 1 LTO-4
Ultrium 1840 SCSI Drive Library
AJ035A
NOTE: Please see
the QuickSpecs for Technical Specifications and additional information:
http://www.hp.com/go/automation
needed to create a complete solution; reference current compatibility information
at: http://www.hp.com/go/ebs.
Disk-Based Backup
RDX Removable Disk Backup
HP StorageWorks RDX160 External
Removable Disk Backup System NOTE: 160GB of Disk Storage
AJ766A
HP StorageWorks RDX320 External
Removable Disk Backup System NOTE: 320GB of Disk Storage
AJ768A
HP StorageWorks RDX500 External
Removable Disk Backup System NOTE: 500GB of Disk Storage
NOTE: Rack-mountable
10 SFF drive enclosure with single I/O module, redundant hot plug power
supplies and hot plug fans. NOTE: Please see the QuickSpecs for Technical Specifications and
additional information: http://h18000.www1.hp.com/products/quickspecs/12245_na/12245_na.html
NOTE: Rack-mountable
12-drive (3.5" 3G SAS/1.5G SATA) 2U enclosure with 3Gb/s SAS host connectivity
and redundant power supplies. NOTE: Please see the QuickSpecs for Technical Specifications and
additional information: http://h18000.www1.hp.com/products/quickspecs/12627_na/12627_na.html
NOTE: Rack-mountable
25-drive (2.5" 3G SAS/1.5G SATA) 2U enclosure with 3Gb/s SAS host connectivity
and redundant power supplies. NOTE: Please see the QuickSpecs for Technical Specifications and
additional information: http://h18000.www1.hp.com/products/quickspecs/12652_na/12652_na.html
NOTE: Cat5e cables
are required to connect Interface Adapters to Console Switches. Cat5e cables
can be found at the following URL: http://www.hp.com/go/kvm.
NOTE: For additional
information regarding KVM switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm.
USB Options
HP 1GB USB 2.0 Floppy Drive Key
442085-B21
USB 1.44-MB External Diskette
Drive
DC141B
USB Floppy Drive
DC361B
HP USB-P/S2 Mouse
DC369A
HP Keyboard (USB) standard 2004
DT528A#ABA
HP USB Internal Cable Kit
451363-B21
Service and Support Offerings (HP Care Pack
Services)
Hardware Services
4-Hour On-site Service
NOTE: To attach
3 year, 4-Hour On-site Service to Smart Buy servers, Smart Buy Care Packs must
be used. For other service levels, order standard Care Pack part numbers.
13-Hour x 5-Day Coverage, 3 Years,
Electronic
U9509E
24-Hour x 7 Day Coverage, 3 Years,
Electronic
U9510E
NOTE: Use one
of the following Smart Buy Care Packs to attach 3 year, 4-Hour On-site Service
to Smart Buy servers. For other service levels, order standard Care Pack part
numbers.
DL16x
Smart Buy 4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
UK159E
DL16x
Smart Buy 4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
UK160E
Hardware
Services Next Business Day On-Site Service
9-Hour
x 5-Day Coverage, 3 Years, Electronic
U9508E
Hardware
Services 6-Hour Call to Repair On-Site Service
NOTE:
Memory configurations listed do not apply to "Factory Integrated Models".
Standard Memory
1GB (2x512MB) or 2GB (2 x 1GB) depending on model, PC2-5300 Fully Buffered
DIMM memory, with Advanced ECC.
Maximum Memory
Up to 32GB memory is available with the optional installation of PC2-5300
Fully Buffered DIMM memory kits. NOTE: Memory should be installed in pairs and matched for optimum
performance.
NOTE:
Chart does not represent all possible memory configurations.
Four Non-hot plug SATA or
four 3.5" Hot-plug SAS/SATA hard drive bays
A
Optional DVD-ROM, or DVD/CD
RW
Drive Support
Removable
Media
Quantity Supported
Position Supported
Controller
DVD-ROM
Up
to 1
A
Integrated IDE (ATAPI) (optional)
DVD/CD
RW
Up
to 1
A
Integrated IDE (ATAPI) (optional)
Hard Drives NOTE: The components of a storage
subsystem (e.g. the drive, the HBA/controller, firmware, and the server
backplane) should operate at the same data transfer rate or the system
bandwidth will be negotiated down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
SATA Non-Hot Plug
3.5" Midline (MDL) Drives
Quantity
Supported
Position
Supported
Controller
250GB 3G SATA 7.2K
500GB 3G SATA 7.2K
750GB 3G SATA 7.2K
Up to 4
1-4
HP Embedded SATA RAID Controller
NOTE: Transfer rate: 1.5 Gb/s SATA
SATA Non-Hot Plug
3.5" Entry (ETY) Drives
Quantity
Supported
Position
Supported
Controller
160GB 3G SATA 7.2K
Up to 4
1-4
HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5 Gb/s SATA
SATA Non-Hot Plug
Drives
Quantity
Supported
Position
Supported
Controller
160GB 1.5G SATA
250GB 1.5G SATA
500GB 1.5G SATA, FIO
Up to 4
1-4
HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5 Gb/s SATA
SATA Hot Plug 3.5"
Midline (MDL) Drives NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
Quantity
Supported
Position
Supported
Controller
160GB 3G SATA 7.2K
250GB 3G SATA 7.2K
500GB 3G SATA 7.2K
750GB 3G SATA 7.2K
1TB 3G SATA 7.2K
Up to 4
1-4
HP Smart Array P400 Controller
HP Smart Array P800 Controller
3.5" SATA Hot
Plug
Quantity
Supported
Position
Supported
Controller
160GB 1.5G SATA 7.2K
250GB 1.5G SATA 7.2K
500GB 1.5G SATA 7.2K
750GB 1.5G SATA 7.2K
Up to 4
1-4
HP SC40Ge 4-Port Internal SAS
HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS
HP Smart Array P400 Controller
HP Smart Array P800 Controller
SATA Hot Plug 3.5"
Midline (MDL) Solid State Drives
Quantity
Supported
Position
Supported
Controller
120GB 3G SATA
60GB 3G SATA
Up to 4
1-4
HP SC40Ge 4-Port Internal SAS
HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS
HP Smart Array P400 Controller
HP Smart Array P800 Controller
SATA Non-Hot Plug
3.5" Entry (ETY) Drives
Quantity
Supported
Position
Supported
Controller
160GB 3G SATA 7.2K
Up to 4
1-4
HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5 Gb/s SATA
SAS Hot Plug 3.5"Midline
(MDL) Drives NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
Quantity
Supported
Position
Supported
Controller
1TB 3G SAS 7.2K
750 3G SAS 7.2K
Up to 4
1-4
Embedded SATA with integrated
SATA RAID 0,1
HP Smart Array E200/128 BBWC Controller
HP Smart Array P400 Controller
HP Smart Array E500/256MB Controller
HP Smart Array P800 Controller
SAS Hot Plug 3.5"
Enterprise (ENT) Drives NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
Quantity
Supported
Position
Supported
Controller
600GB 6G SAS 15K
450GB 6G SAS 15K
450GB 3G SAS 15K
300GB 3G SAS 15K
146GB 3G SAS 15K
72GB 3G SAS 15K
Up to 4
1-4
HP SC40Ge 4-Port Internal SAS
HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS
HP Smart Array P400 Controller
HP Smart Array P800 Controller
NOTE: For a complete listing of compatible tape and disk-based
backup offerings, please visit: www.hp.com/go/connect NOTE: SAS Tape Drives: Connecting hard drive cage and SAS tape
to the same SAS Controller using split cable (supplied with tape drive)
deactivates 1 of the hard drive bays. Actual hard drive bay deactivated
depends on where split cable plugs into SAS drive connector. Example:
3x SAS cable connector plugged into SAS drive connector (5-8) on the back
of the hard drive cage would mean drive bay 8 is deactivated.
Position
Supported
Controller
Controller/HBA Option Kit Part Number
HP
StorageWorks SCSI Tape Drives, External
LTO-1 Ultrium 232
LTO-2 Ultrium 448
LTO-3 Ultrium 920
LTO-3 Ultrium 960
LTO4 Ultrium 1760
LTO-4 Ultrium 1840
DAT 40
DAT 72
DAT 160
1U Rack-Mount Kit
3U Rack-Mount Kit
HP StorageWorks
USB Tape Drives, External
DAT 40 USB
DAT 72 USB
DAT 160 USB
1U USB Rack-Mount Kit
External
USB 2.0 Port
N/A
HP
StorageWorks SAS Tape Drives, External
DAT 160 SAS
LTO-2 Ultrium 448 SAS
LTO-3 Ultrium 920 SAS
LTO-4 Ultrium 1760 SAS
LTO-4 Ultrium 1840 SAS
1U Rack-Mount Kit
3U Rack-Mount Kit
System Leakage with all power
supplies loaded (mA)
1.58
3.03
System Inrush Current with
all power supplies loaded (A)
19
37
Power cord requirements
Nema 5-15P to IEC320-C13
IEC320-C13 to IEC320-C14
NOTE: Power shown
is for a fully configured system consisting of (2) CPU, (8) double-sided
DIMMs, (2) HDDs, (1) CD-ROM, and (2) PCI cards.
Power Cord
AF556A
Server Power Cords
One 6' Highline (IEC-IEC) power cord ships standard NOTE:
HP ProLiant DL servers no longer ship standard with NEMA power cords (163719-002)
that allow connection to 110V wall outlets in a home or office. ProLiant DL servers
are primarily connected to PDU's in data center racks so they now ship standard
with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant
DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001)
must be ordered separately.
If customers require a local power
cord, they can check the power cord matrix for the appropriate cord. Please see
the following power cord matrix: http://www.hp.com/go/powercordmatrix.
- Click on the system of interest. Example: DL160 G5
- Follow the instructions of the next screens.
Power Supply Output (per
power supply)
Rated Steady-State
Power
653.10W (at 100 VAC),
653.08W (at 200 VAC)
System
Inlet Temperature
Operating
50°
to 95° F (10° to 35° C) at sea level with an altitude derating of
1.8°F per every 1000 ft (1.0°C per every 305 m) above sea level to a maximum
of 10,000 ft (3050 m), no direct sustained sunlight. Maximum rate of change is
18°F/hr (10°C/hr). The upper limit may be limited by the type and number
of options installed. System performance may be reduced if operating with
a fan fault or above 86°F (30°C).
Non-operating
40°
to 140° F (-40° to 60° C) Maximum rate of change is 36°F/hr
(20°C/hr).
Relative
Humidity (non-condensing)
Operating
10%
to 85% relative humidity (Rh), 82.4°F (28°C) maximum wet bulb temperature,
non-condensing.
Non-operating
10%
to 95% relative humidity (Rh), 101.7°F (38.7°C) maximum wet bulb temperature,
non-condensing.
Altitude
Operating
10,000
ft (3050 m). This value may be limited by the type and number of options installed.
Maximum allowable altitude change rate is 1500 ft/min (457 m/min).
Non-operating
30,000
ft (9144 m). Maximum allowable altitude change rate is 1500 ft/min (457 m/min).
Acoustic Noise
Listed
are the declared A-Weighted sound power levels (LWAd) and declared
average bystander position A-Weighted sound pressure levels (LpAm)
when the product is operating in a 23°C ambient environment. Noise emissions
were measured in accordance with ISO 7779 (ECMA 74) and declared in accordance
with ISO 9296 (ECMA 109).
Idle
LWAd
6.86
LpAm
52.36dBA
Operating
LWAd
6.89
LpAm
52.60dBA
Emissions
Classification (EMC)
FCC Rating
Class
A
Normative Standards
CISPR
22; EN55022; EN55024; FCC CFR 47, Pt 15; ICES-003; CNS13438; GB9254; K22;K24;
EN 61000-3-2; EN 61000-3-3; EN 60950-1; IEC 60950-1
NOTE:
Product conformance to cited product specifications is based on sample (type)
testing, evaluation, or assessment. This product or family of products is eligible
to bear the appropriate compliance logos and statements.
Combines a triple-speed
IEEE 802.3TM - Compliant Media Access Controller (MAC) with a triple-speed
Ethernet transceiver.
Data Transfer Method
Compliant to x1 PCIe
Specification
Network Transfer
Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX (Half and Full-Duplex)
2000Mb/s
Connector
RJ-45 connector
Cable Support
Performs all the physical
layer functions for 10BASE-T, 100BASE-T, and 1000BASE-T Ethemet on standard
Category 5 UTP
Environment-friendly
Products and Approach
End-of-life
Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go to: http://www.hp.com/go/green.
To recycle your product, please go to: http://www.hp.com/go/green
or contact your nearest HP sales office. Products returned to HP will be recycled,
recovered or disposed of in a responsible manner.
The EU WEEE directive
(2002/95/EC) requires manufacturers to provide treatment information for each
product type for use by treatment facilities. This information (product disassembly
instructions) is posted on the Hewlett Packard web site at: http://www.hp.com/go/green.
These instructions may be used by recyclers and other WEEE treatment facilities
as well as HP OEM customers who integrate and re-sell HP equipment.