Low-profile slot cover (slot only
accessible in G5 system)
10.
Optional 3rd and 4th 3.5"
hot-plug SAS/SATA or non-hot plug SATA hard drive bays
10.
Full-sized riser board assembly
slot cover
11.
Standard 1st and 2nd 3.5"
hot-plug SAS/SATA or non-hot plug SATA hard drive bays
12.
Full height/full length PCI-Express
or HTX slot
What's New
Support for SATA Hot Plug 3.5" Midline (MDL) Solid State Drives
Support for SAS Hot Plug 3.5" Enterprise (ENT) Hard Drives
At A Glance
Introducing the HP ProLiant DL165G5p, now available with the latest high
performance Opteron Quad Core processors, increased storage by 2X and
a new high efficiency power supply option.
Processors:
Supports up to two AMD Opteron™ 2300 series Quad-Core processors
Supports DirectConnect Architecture
Supports Power Now
Memory:
16 DIMM slots supporting up to 64GB REG PC2-6400 DDR2-800 MHz memory
with Advanced ECC
16 DIMM slots supporting up to 128GB REG PC2-5300 DDR2-667 MHz memory
with Advanced ECC
Internal Drive Support:
Internal storage capacity:
SATA Capacity: Support for up to 4.0TB (4 x 1TB) in Hot Plug
Model. Support for up to 3.0TB (4x750GB) in Non Hot Plug Model.
SAS Capacity: Support for up to 4.0 TB (4 x 1TB) in Hot Plug
Model
NOTE: Installation of the Hot
Plug Backplane 1U 2S Kit (445985-B21) is required if ordering
third or fourth Hard Drives for Hot Plug models only.
Network Controller:
Embedded HP NC362i Integrated Dual Port Gigabit Server Adapter
Storage Controllers:
Non-Hot Plug SATA Models: HP Embedded SATA Controller
Hot Plug SATA/SAS Models: HP SC40Ge SAS HBA with RAID 0,1 NOTE: When using the SC40Ge
with SATA Hard Drives, 1.5G SATA Hard Drives are required.
Expansion Slots:
Standard - PCI-Express assembly includes:
Slot 1: full-length/full height PCI-Express x16
Infrastructure Management:
HP ProLiant Lights Out 100i Remote Management support (IPMI 2.0
and SMASH support)
Virtual Media plus Virtual KVM support with LO100i Advanced license
HP Insight Control for Linux (IC-Linux), a product option, delivers
essential infrastructure management that can help save time and money
by making it easy to deploy, monitor, control and optimize your IT
infrastructure through a single, simple management console. HP Insight
Control for Linux supports Linux-based servers and management consoles.
USB Ports:
Up to five USB ports (two front & two rear standard, 1 internal
option)
Optical Drive:
Support for one (optional): DVD-ROM, DVD/CD RW
Power Supply:
650W Power Supply standard (Non-Hot Plug, Autoswitching)
Form Factor:
Rack (1U)
Fixed mounting rails included with all models
Deployment/Serviceability:
Tool-less access to all system components for easy in-rack serviceability
Customer Self Repair (CSR): HP products are designed with many CSR
parts to minimize repair time and allow for greater flexibility in
performing defective parts replacement
Warranty:
This product is covered by a global limited warranty and supported
by HP Services and a worldwide network of HP Authorized Channel Partners.
Hardware diagnostic support and repair is available for one year from
date of purchase. Support for software and initial setup is available
for 90 days from date of purchase. Enhancements to warranty services
are available through HP Care Pack services or customized service
agreements. Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details. NOTE: Server Warranty includes
1 year Parts, 1 year Labor, 1-year on-site support with next business
day response. Warranty repairs may be accomplished through the use
of Customer Self Repair (CSR) parts. These parts fall into two categories:
1) Mandatory CSR parts are designed for easy replacement. A travel
and labor charge will result when customers decline to replace a Mandatory
CSR part; 2) Optional CSR parts are also designed for easy replacement
but may involve added complexity. Customers may choose to have HP
replace Optional CSR parts at no charge. Additional information regarding
worldwide limited warranty and technical support is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
NOTE: For the Standard Features shipped in
the "Factory Integrated Models", please see the "Configuration
Information - Factory Integrated Models" section.
Processor One of the following depending
on Model
AMD Opteron™
processor Model 2393SE (3.1GHz, 105W ACP)
AMD
Opteron™ processor Model 2389 (2.9GHz, 75W ACP)
AMD
Opteron™ processor Model 2384 (2.7GHz, 75W ACP)
AMD
Opteron™ processor Model 2381HE (2.5GHz, 55W ACP)
AMD
Opteron™ processor Model 2380 (2.5GHz, 75W ACP)
AMD
Opteron™ processor Model 2377EE (2.3GHz, 50W ACP)
AMD
Opteron™ processor Model 2376 HE (2.3GHz, 55W ACP) NOTE:
Offered through Configure-To-Order only. See Factory Integrated Models section
for more details.
AMD
Opteron™ processor Model 2376 (2.3GHz, 75W ACP)
AMD
Opteron™ processor Model 2374 HE (2.2GHz, 55W ACP)
Upgradeability
Upgradeable to two processors
Chipset
ServerWorks HT2100 and HT1000
Cache Memory
6MB shared L3 cache
Memory Protection
Advanced ECC
Memory One of the following depending on Model
Type
REG PC2-6400 DIMMs
(DDR2-667)
REG PC2-5300 DIMMs
(DDR2-667)
NOTE:
DIMM banks are active only when the corresponding processor socket is populated.
Standard
(Model 2376)
2 GB
(2 x 1 GB)
Standard
(Model 2380)
4 GB
(2 x 2 GB)
Standard
(Model 2384)
8 GB
(4 x 2 GB)
Maximum
64 GB
(16 x 4 GB)
Network Controller
Embedded NC362i dual-port gigabit
server adapter
Expansion Slots #
Technology
Bus Width**
Connector Width
Bus Number*
Form Factor
Notes
1
PCI Express
x16
x16
3
Full Height/Full Length
*
Default bus assignment. Inserting cards with PCI bridges may alter the actual
bus assignment number.
**
Slots are enumerated differently based on OS. MS OS's enumerate from lowest
to highest Device ID by bus (starting with the lowest bus).
Storage Controller
Non-Hot Plug SATA
HP Embedded SATA Controller
Hot Plug SATA/SAS
HP SC40Ge SAS HBA with RAID
0,1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required.
NOTE:
A diskette drive is needed to install storage controller drivers during
a Windows operating system installation from CD.
Storage
Diskette Drives
Via USB only
Optical Drives
Optional 8x IDE (ATAPI) DVD-ROM
drive, slim
Optional 24x IDE (ATAPI) DVD-ROM/CDRW
drive
Hard Drives
Up to 4 Non-hot plug SATA 3.5"
drives
Up to 4 Hot plug SATA /SAS 3.5"
drives
Maximum Internal
Storage
Non-Hot Plug SATA
3.0TB
4 x 750GB
Hot Plug SATA
4.0TB
4 x 1TB
Hot Plug SAS
4.0TB
4 x 1TB
Interfaces
Parallel
None
Network RJ-45(Ethernet)
HP NC362i Integrated Dual Port
Gigabit Server Adapter
HP Lights-Out 100i Remote Management delivers affordable, entry level
remote management capabilities for HP ProLiant 100 Series servers with
embedded LO100i. It allows customers or their service providers to remotely
manage ProLiant 100 Series servers remotely over a LAN or the Internet
and consists of the following:
LO100i Standard is embedded remote management and provides
basic remote control via telnet, browser, and IPMI 2.0 and SMASH and
comes standard on all DL100 series servers except for the DL180 G1 and
G5 and the DL120 G5 servers.
LO100i Advanced Pack License are upgrades for essential, secure,
remote control, serial console and virtual media plus Virtual KVM (graphical
hardware-based, remote console).
NOTE: Flexible and volume quantity (AKA)
license kits are available for the Lights-Out 100i Advanced Pack licenses
as well as Electronic License To Use (E-LTU). AKA Tracking licenses require
a 100 unit minimum forecast at initial contract signing. For these additional
part numbers, please refer to each software products. QuickSpecs at this
link for more information: www.hp.com/go/lo100
Core Infrastructure
Management
HP Insight Control for Linux
HP Insight Control for Linux, as a product option, delivers essential
infrastructure management that can help save time and money by making
it easy to deploy, monitor, remote control, and optimize your IT infrastructure
through a single, simple management console. The Insight Control for Linux
suite installs and license software modules that are integrated into HP
System Insight Manager.
The HP Insight Control suite for Linux (IC-Linux) serves environments
requiring a Linux-based management consoles. See www.hp.com/go/ic-linux
HP Insight Control suites include one year of 24 x 7 HP Software Technical
Support and Update Service ensuring rapid access to HP support staff and
proactive delivery of software updates. For more information about this
service, please visit: www.hp.com/services/insight.
Insight Control server deployment
HP Insight Control server deployment
is a deployment solution for HP ProLiant and Integrity servers hosted on
a Windows CMS. It automates the process of deploying and provisioning server
software, enabling companies to quickly and easily adapt to changing business
demands. Insight Control server deployment includes software optimizations
for HP servers, including the HP scripting toolkits, configuration jobs
for leading industry-standard operating systems, sample unattended files,
and HP server support packs that include software drivers, management agents,
and important documentation. Deploying servers can be accomplished either
through imaging or through scripting.
Insight Control server deployment is hosted on a Windows server and is intended
for heterogeneous environments deploying Windows, Linux, VMware ESX and
Microsoft Hyper-V systems.
Insight Control server deployment includes one year of 24 x 7 HP Software
Technical Support and Update Service ensuring rapid access to HP support
staff and proactive delivery of software updates. For more information about
this service, please visit: http://www.hp.com/services/insight.
Industry Standard
Compliance
ACPI V2.0 Compliant
PCI 2.2 Compliant
PXE Support
WOL Support
Microsoft® Logo certifications
IPMI 2.0, SMASH CLP Compliant
Manageability
Embedded HP ProLiant Lights-Out 100i Remote Management, with licensable
upgrades to Lights-Out 100i Advanced.
Security
Power-on password
Setup password
UPS and PDU Power
Cord Matrix
Please see the UPS and PDU cable
matrix's on the HP Power Protection and Management page. Under Power Cords,
click on the "HP Power Cord Matrix" link. That link will list
cable descriptions, requirements, and specifications for UPS and PDU units.
Please see the following link: www.hp.com/products/powercords.
NOTE: For more information on HP's
Certified and Supported ProLiant Servers for OS and Virtualization Software
and latest listing of software drivers available for your server, please
visit our Support Matrix at: http://www.hp.com/go/supportos
our driver download page http://www.hp.com/support/DL165G5p
Rack Airflow Requirements
Rack 10000 G2 series Cabinets
The increasing power of new high-performance processor technology requires
increased cooling efficiency for rack-mounted servers. The 10000 G2 Series
Racks provide enhanced airflow for maximum cooling, allowing these racks
to be fully loaded with servers using the latest processors.
CAUTION: If a third-party rack is
used, observe the following additional requirements to ensure adequate airflow
and to prevent damage to the equipment:
Front and rear doors: If your 42U server rack includes closing front and
rear doors, you must allow 5,350 sq cm (830 square inches) of hole evenly
distributed from top to bottom to permit adequate airflow (equivalent to
the required 64 percent open area for ventilation).
Side: The clearance between the installed rack component and the side panels
of the rack must be a minimum of 7 cm (2.75 inches)
CAUTION: Always use blanking panels
to fill all remaining empty front panel U-spaces in the rack. This arrangement
ensures proper airflow. Using a rack without blanking panels results in
improper cooling that can lead to thermal damage.
Rack Support
The DL Fixed Rail System supports
installation in racks with square or round mounting holes (including Compaq/HP
7000, 9000, 10000 and HP series), with an adjustment range of 24" -
36".
Telco Rack Kit
Installation into Telco 2 post, and 4 post, or threaded holes racks requires
a 3rd party option kit. For additional information, please visit: www.hp.com/go/rackandpower.
HP Factory Express Capability
HP Factory Express offers configuration, customization, integration and
deployment services for HP servers and storage products. Customers can
choose how their factory solutions are built, tested, integrated, shipped
and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as individual
factory services, such as image loading, asset tagging, and custom packaging.
HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades,
HP BladeSystem, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP,
rackable tape libraries and configurable network switches.
For more information on Factory Express services for your specific server
model please contact your sales representative or go to: http://www.hp.com/go/factory-express.
HP Enterprise Configurator
The HP eConfigure Enterprise Configurator now provides factory default
racking for our HP hardware portfolio. This approach is aligned with our
strategic direction to meet the needs and expectations of our valued customers.
If you require "custom" rack configuration, please contact HP's
Customer Business Center or an Authorized Partner for assistance.
Service and Support
HP Care Pack Services provide total care and support expertise with committed
response designed to meet your IT and business needs.
HP Care Pack services include coverage for the HP branded hardware options
qualified for the server that are purchased at the same time or afterward
and internal to the enclosure. It also includes the 22" and smaller
external monitors and tower UPS options up to 3kVA. These items will be
covered at the same service level and for the same coverage period as
the server. Coverage of UPS Battery is not included and standard warranty
terms & conditions apply. For servers or storage systems installed
within a rack, service also covers all HP qualified rack options installed
within the same rack.
To fully capitalize on your HP ProLiant servers' capabilities requires
a service partner who thoroughly understands your server technology and
systems environment. HP Services, an industry leader in provision of multi
vender support solutions provides a range of support services designed
to meet the varying needs of business. Whether an SMB or large global
corporation HP has a ProLiant server support offer to help you speedily
deploy and maximize system uptime.
Recommended Service - Simplify ProLiant solution implementation,
maintenance and management.
Support Service -3 Year, 9x5 Next Business Day coverage, excluding
HP holidays only
Deployment Service - Hardware Installation only
Enhanced Service - Optimize service level to increase IT performance
and availability
Support Service - 3 Year 13x5 Same Business Day, 4-Hour response
coverage
Deployment Service - Installation and Start-up only
Installation & Start-Up of a ProLiant server and Microsoft or Linux
O/S per the Customer Description and/or Data Sheet. To be delivered on
a scheduled basis 8am-5pm, M-F, excl. HP holidays.
NOTE:
High Performance Computing (HPC) interconnect technologies are available
for the DL165 G5p under the Cluster Platform product portfolio. These high-speed
interconnects are fully supported by HP when they are part of these configure
to order clusters. Solutions can be defined with a lot of flexibility with
the help of configuration tools. Please visit the following URL to configure
HPC Clusters with InfiniBand, Gigabit Ethernet or Myrinet Interconnects:
http://www.hp.com/techservers/clusters/ucp/index.html
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure
a Factory Integrated Model. To ensure only valid configurations are ordered,
HP recommends the use of an HP approved configurator. Contact your local
sales representative for information on CTO product offerings and requirements. NOTE: HP does not allow factory integration of options into standard
models listed above. Configure-to-order servers must start with a CTO
Chassis. NOTE: FIO indicates that this option is only available as a Factory
Installable Option.
Step 1: Base Configuration
Non-Hot Plug SATA Model
HP ProLiant DL165 G5p Non-Hot
Plug SATA Rack Chassis
495842-B21
Factory Integrated Model ships
with:
HP NC362i Integrated Dual Port
Gigabit Server Adapter
One available PCI-Express slots, including one full-length/full height
slot
HP embedded SATA controller
650 Watt Power Supply
6 Fixed, Non-Redundant Fans
Rack (1U), (1.75 in / 4.45 cm)
Fixed Mounting Rails
Hot Plug SATA/SAS Model
HP ProLiant DL165 G5p Hot Plug
SATA/SAS Rack Chassis
495841-B21
Factory Integrated Model ships
with:
HP NC362i Integrated Dual Port
Gigabit Server Adapter
One full-length/full height PCI-Express
slot houses the SATA/SAS storage controller
650 Watt Power Supply
6 Fixed, Non-Redundant Fans
Rack (1U), (1.75 in / 4.45 cm)
Fixed Mounting Rails
Step
2: Choose Required Options (only one of the following from each list unless otherwise
noted)
Processors
AMD
Opteron™ processor Model 2393SE (3.1GHz, 105W ACP), FIO
500062-B21
AMD
Opteron™ processor Model 2389 (2.9GHz, 75W ACP), FIO
500049-B21
AMD Opteron™ processor
Model 2384 (2.7GHz, 75W ACP), FIO NOTE:
If 2 processors are desired, select one 500064-B21 and one 500064-B21.
500064-B21
AMD
Opteron™ processor Model 2381HE (2.5GHz, 55W ACP), FIO
500058-B21
AMD Opteron™ processor
Model 2380 (2.5GHz, 75W ACP), FIO NOTE:
If 2 processors are desired, select one 500060-B21 and one 500060-B21.
500060-B21
AMD
Opteron™ processor Model 2377EE (2.3GHz, 50W ACP), FIO
536530-B21
AMD Opteron™ processor
Model 2376 HE (2.3GHz, 55W ACP), FIO NOTE:
If 2 processors are desired, select one 507540-B21 and one 507540-B21.
507540-B21
AMD
Opteron™ processor Model 2376 (2.3GHz, 75W ACP), FIO NOTE:
If 2 processors are desired, select one 500056-B21 and one 500056-B21.
500056-B21
AMD Opteron™ processor
Model 2374 HE (2.2GHz, 55W ACP), FIO NOTE:
If 2 processors are desired, select one 500051-B21 and one 500051-B21.
500051-B21
Memory
NOTE: DIMM banks
are active only when the corresponding processor socket is populated.
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and
the server backplane) should operate at the same data transfer rate or the
system bandwidth will be negotiated down to an acceptable level for all
components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
Serial-ATA (SATA) Non-Hot
Plug Hard Drives (Non-Hot Plug Models Only)
NOTE: The previous
generation of 1.5G SATA drives are still supported.
Storage Controllers
NOTE: Storage
Controller only required if 445148-B21 is selected in Step 1 above.
HP Smart Array E500/256MB Controller
with Battery, FIO NOTE: Customers can only order one
Smart Array E500/256MB Controller and one Battery-backed write cache upgrade
(P/N 383280-B21) for the HP ProLiant DL165 G5p server based on battery space.
HP SC40Ge SAS HBA, FIO NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required.
449176-B21
HP SA-P400 and SA-E500 24 In Battery
Cable Kit NOTE: This option kit contains a
24" battery cable and adhesive material for installing a battery into
the following servers if a Smart Array E500 is integrated outside of the
factory. For all solutions, please refer to the HP ProLiant QuickSpecs and
User's Manual for detailed installation instruction.
Battery-backed write cache NOTE: When installing a battery-backed
write cache module, the HP Smart Array E500 must be installed in the full-length
PCI slot. 256MB Battery-backed write cache upgrade for RAID 5 support.
Hot Plug HDD Backplane 1U 2S Kit NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only in Step 1 above.
445985-B21
Power Supplies
HP 1200W High Efficiency Power
Supply Kit, FIO NOTE: Selection of the HE Power Supply
Unit will remove the 650 Watt standard power supply and requires the purchase
of Power Supply Backplane (P/N 453652-B21).
453650-B21
Power Options
Power Supply Backplane, FIO NOTE: This backplane must be ordered
with the high efficiency power supply (P/N 453650-B21).
453652-B21
Step 4: Choose Additional Options
for Factory Integration
NOTE: For additional
"Core Options" and "Additional Options", please refer
to the options sections below.
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and
the server backplane) should operate at the same data transfer rate or the
system bandwidth will be negotiated down to an acceptable level for all
components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
Serial-ATA (SATA) Non-Hot
Plug Hard Drives (Non-Hot Plug Models Only)
HP NC522SFP Dual Port 10GbE Server
Adapter NOTE: A minimum of two Gigabytes
(2 GB) of server memory is required per each NC522SFP adapter. NOTE: Direct Attach Cable (DAC) for copper environments or fiber
transceivers and cables for fiber-optic environments must be purchased separately.
HP LO100i Advanced Pack, No Media
1-Server License including 1 year of 24x7 Technical Support and Updates
530521-B21
NOTE: Flexible
and volume quantity (AKA) license kits are available for the Lights-Out
100i Advanced Pack licenses as well as Electronic License To Use (E-LTU).
AKA Tracking licenses require a 100 unit minimum forecast at initial contract
signing. For these additional part numbers, please refer to QuickSpecs at
this link for more information: www.hp.com/go/lo100
HP Insight Software
HP Insight Control for Linux
HP Insight Control for Linux,
1-server license, including one year of 24x7 Technical Support and Updates,
Electronic
T9084BAE
HP Insight Control for Linux,
No Media, 1-Server license, including one year of 24x7 Technical Support
and Updates
464423-B22
HP Insight Control for Linux,
Media pack (DVD) - No licenses included NOTE: Media pack DVD contains HP
Insight Control for Linux, HP Systems Insight Manager, HP Insight Control
power management, HP Insight Control virtual machine management, and an
integrated installer. Licenses must be acquired separately NOTE: This Media pack is optional because the latest ISO image and
latest updates may be downloaded at no cost from: http://www.hp.com/go/ic-linux
(click on Download button).
464422-B22
NOTE: Electronic
licenses can be used to purchase multiple licenses with a single activation
key, and are available in all countries except China and Japan. Customers
in China and Japan should order the physical equivalent. NOTE: Customer will receive a license entitlement certificate, which
must be redeemed online or via fax in order to obtain the license activation
key(s). Includes one year of 24 x 7 HP Software Technical Support Service. NOTE: For additional License Kits, including electronic licensing
options, please see the QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/13019_na/13019_na.html
HP Insight Control server deployment
HP Insight Control server deployment
Electronic License including 1 year 24x7 Technical Support and Updates
T9082AAE
HP Insight Control server deployment
1-Server License including 1 year 24x7 Technical Support and Updates
452151-B21
NOTE: Licenses
ship without media. The Insight Control Media Kit can be ordered separately,
or can be downloaded at: http://www.hp.com/go/insightupdates.
NOTE: Electronic licenses can be used to purchase multiple licenses
with a single activation key, and is available in all countries except China
and Japan. Customers in China and Japan should order the physical equivalent.
NOTE: Customer will receive a license entitlement certificate, which
must be redeemed online or via fax in order to obtain the license activation
key(s). Includes one year of 24 x 7 HP Software Technical Support Service. NOTE: For additional license kits please see the Insight Control
QuickSpecs at: http://h18004.www1.hp.com/products/quickspecs/12631_na/12631_na.html
Hot Plug HDD Backplane Option
Hot Plug HDD Backplane 1U 2S Kit
NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
445985-B21
Storage Controllers
NOTE: The addition
of storage controllers for internal hard drive use is intended for use ONLY
with the Hot Plug SATA/SAS Model Chassis (495841-B21).
HP Smart Array P400/256MB Controller NOTE: Customers can only order one
Smart Array P400/256MB Controller and one Battery-backed write cache upgrade
(P/N 383280-B21) for the HP ProLiant DL165 G5 server based on battery space.
HP Smart Array P400/512MB BBWC
Controller NOTE: Customers can only order one
Smart Array P400/512MB BBWC Controllers for the HP ProLiant DL165 G5p server
based on battery space.
HP SA-P400 and SA-E500 24 In Battery
Cable Kit NOTE: This option kit contains a
24" battery cable and adhesive material for installing a battery into
the following servers if a Smart Array E500 is integrated outside of the
factory. For all solutions, please refer to the HP ProLiant QuickSpecs and
User's Manual for detailed installation instruction.
HP StorageWorks 1U USB Rack-Mount
Kit with one DAT 160 USB Tape Drive NOTE: Pre-configured with one DAT
160 USB tape drive.
AG703A
SAS Rack-Mount Tape Solutions NOTE: HP recommends purchasing the
HP SC44Ge HBA ( 416096-B21) for a dedicated SAS HBA for tape.
HP StorageWorks 1U SAS Rack-Mount
Kit with one LTO-4 Ultrium 1760 NOTE: Pre-configured with one LTO-4
Ultrium 1760 SAS tape drive.
EH946A
HP StorageWorks 1U SAS Rack-Mount
Kit NOTE: Supports up to (2) half-height
SAS tape drives.
AE459A
HP StorageWorks DAT 160 SAS Internal Tape Drive NOTE: Mounts inside the 1U SAS
Rack-Mount Kit (AE459A).
Q1587A
HP StorageWorks LTO-2 Ultrium 448 SAS Internal Tape Drive NOTE: Mounts inside the 1U SAS
Rack-Mount Kit (AE459A).
DW085A
HP StorageWorks LTO-3 Ultrium 920 SAS Internal Tape
Drive NOTE: Mounts inside the 1U SAS
Rack-Mount Kit (AE459A).
EH847A
SCSI Rack-Mount Tape Solutions NOTE: SCSI Controller required. HP
recommends purchasing the HP SC11Xe HBA ( 412911-B21) for a dedicated SCSI
HBA for tape.
HP StorageWorks 1U SCSI Rack-mount
kit with one LTO-2 Ultrium 448 SCSI Tape Drive (Carbonite) NOTE: Pre-configured with one LTO-2
Ultrium 448 SCSI tape drive.
DW028B
HP StorageWorks 1U SCSI Rack-mount
kit with one LTO-3 Ultrium 920 NOTE: Pre-configured with one LTO-3
Ultrium 920 SCSI tape drive.
EH903A
HP StorageWorks 3U SCSI Rack-Mount
with 1 LTO-4 Ultrium 1840 Tape Drive NOTE: Pre-configured with one LTO-4
Ultrium 1840 SCSI tape drive.
EH926A
NOTE: For an up-to-date
listing of the latest O/S and software support details for HP Ultrium tape
drives, please visit: http://www.hp.com/go/connect
Tape Autoloaders
HP StorageWorks DAT Autoloader
HP StorageWorks DAT 72x10 tape
autoloader
AE313B
HP StorageWorks 1/8 G2 Tape Autoloader
HP StorageWorks 1/8 G2 LTO-4 Ultrium
1760 SAS Tape Autoloader
AK377A
HP StorageWorks 1/8 G2 LTO-3 Ultrium
920 SAS Autoloader
AH558A
HP StorageWorks 1/8 G2 LTO-2 Ultrium
448 Tape Autoloader
AH164A
HP StorageWorks 1/8 G2 Tape Autoloader
Rack Kit NOTE: Required to install the 1/8
G2 Autoloaders in a standard 19-inch rack; includes rails and rackmount
instructions.
AH166A
NOTE: Please reference
the QuickSpecs for Technical Specifications and http://www.hp.com/go/automation
for additional information needed to create a complete solution; reference
current compatibility information at: http://www.hp.com/go/ebs.
Tape Libraries
HP StorageWorks MSL2024 Tape Library
HP StorageWorks MSL2024 1 LTO-4
Ultrium 1840 SCSI Drive Library
AJ033A
HP StorageWorks MSL2024 1 LTO-4
Ultrium 1760 SAS Drive Library
AK378A
HP StorageWorks MSL2024 1 LTO-3
Ultrium 960 SCSI Drive Library
HP StorageWorks 50 Modular Smart
Array NOTE: Rack-mountable 10 SFF drive
enclosure with single I/O module, redundant hot plug power supplies and
hot plug fans.
NOTE: Rack-mountable
12-drive (3.5" 3G SAS/1.5G SATA) 2U enclosure with 3Gb/s SAS host connectivity
and redundant power supplies. NOTE: Please see the QuickSpecs for Technical Specifications and
additional information: http://h18000.www1.hp.com/products/quickspecs/12627_na/12627_na.html
NOTE: Rack-mountable
25-drive (2.5" 3G SAS/1.5G SATA) 2U enclosure with 3Gb/s SAS host connectivity
and redundant power supplies. NOTE: Please see the QuickSpecs for Technical Specifications and
additional information: http://h18000.www1.hp.com/products/quickspecs/12652_na/12652_na.html
HP 4.9 kVA S124 Monitored PDU-
single input, 1Ø, 24A
AF914A
Modular Power Distribution Units
1U/0U (Up to 32 outlets)
NOTE: 1U/0U mounting
brackets shipped with the unit (optimized for 10000 G2 and 9000 series racks).
HP Modular Power Distribution
Units (mPDU), Low Volt Model, 24A (100-127 VAC) NOTE: This mPDU ( 252663-D71) may
also be used to connect the low volt model of the UPS R3000 XR.
HP Modular Power Distribution
Units (mPDU), High Volt Model, 16A (200-240 VAC) NOTE: This PDU has a detachable input
power cord and allows for adaptability to country specific power requirements.
NOTE: Please see
the following Modular Power Distribution Unit (Zero-U/1U Modular PDUs) QuickSpecs
for additional options including shorter jumper cables and country specific
power cords: http://h18000.www1.hp.com/products/quickspecs/11041_na/11041_na.html NOTE: For additional information on HP Power Distribution Units including
accessories please go to: www.hp.com/go/pdu.
NOTE: For additional
information regarding KVM switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm.
USB Options
HP USB Internal Cable Kit
451363-B21
1.44MB External USB Floppy Drive
All
DC141B
USB Floppy Drive
DC361B
USB P/S2 Optical Mouse
DC369A
USB Standard Keyboard
DT528A#ABA
Service and Support
Offerings
(HP Care Pack Services)
Hardware Services 4-Hour On-site
Service
13-Hour x 5-Day Coverage, 3 Years,
Electronic
U9509E
24-Hour x 7-Day Coverage, 3 Years,
Electronic
U9510E
Hardware Services Next Business
Day On-Site Service
9-Hour x 5-Day Coverage, 3 Years,
Electronic
U9508E
Hardware Services 6-Hour Call
to Repair On-Site Service
NOTE:
Memory configurations listed do not apply to "Factory Integrated Models".
HP ProLiant DL165
G5p (all models)
Standard Memory
2 GB (2 x 1 GB) PC2-6400 DIMM memory, with Advanced ECC Capabilities memory
installed. Maximum Memory
Up to 128GB memory is available with the optional installation of PC2-5300
Registered DIMM memory kits.
Memory should be installed in pairs and matched for optimum performance.
NOTE:
Chart does not represent all possible memory configurations. NOTE: DIMM banks are active only when the corresponding processor
socket is populated.
Non-hot plug 3.5" SATA or
Hot-plug SAS/SATA hard drive bays
A
Optional DVD-ROM, or DVD/CD RW
Drive Support
Removable Media
Quantity
Supported
Position
Supported
Controller
DVD-ROM
Up to 1
A
Integrated IDE (ATAPI) (optional)
DVD/CD RW
Up to 1
A
Integrated IDE (ATAPI) (optional)
Hard Drives NOTE: The components of a storage
subsystem (e.g. the drive, the HBA/controller, firmware, and the server
backplane) should operate at the same data transfer rate or the system
bandwidth will be negotiated down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
SATA Non-Hot Plug
3.5" Entry (ETY) Drives
Quantity
Supported
Position
Supported
Controller
160GB 3G SATA 7.2K
Up to 4
1-4
HP Embedded SATA Controller
SATA Non-Hot Plug
3.5" Midline (MDL) Drives
Quantity
Supported
Position
Supported
Controller
750GB 3G SATA 7.2K
500GB 3G SATA 7.2K
250GB 3G SATA 7.2K
Up to 4
1-4
HP Embedded SATA Controller
3.5" SATA Non-Hot
Plug Drives
Quantity
Supported
Position
Supported
Controller
500GB 1.5G SATA,FIO
250GB 1.5G SATA 7.2K
160GB 1.5G SATA 7.2K
Up to 4
1-4
HP Embedded SATA Controller
SATA Hot Plug 3.5"
Entry (ETY) Drives NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
Quantity
Supported
Position
Supported
Controller
160GB 3G SATA 7.2K
Up to 4
1-4
HP Embedded SATA Controller
SATA Hot Plug 3.5"
Midline (MDL) Drives
Quantity
Supported
Position
Supported
Controller
1TB 3G SATA 7.2K
750GB 3G SATA 7.2K
500GB 3G SATA 7.2K
250GB 3G SATA 7.2K
Up to 4
1-4
HP Embedded SATA Controller
SATA Hot Plug 3.5"
Midline (MDL) Solid State Drives
Quantity
Supported
Position
Supported
Controller
120GB 3G SATA
60GB 3G SATA
Up to 4
1-4
HP SC40Ge 4-Port Internal SAS
HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS
HP Smart Array P400 Controller
HP Smart Array P800 Controller
SAS Hot Plug 3.5"
Enterprise (ENT) Drives
Quantity
Supported
Position
Supported
Controller
600GB 6G SAS 15K
450GB 6G SAS 15K
450GB 3G SAS 15K
300GB 3G SAS 15K
146GB 3G SAS 15K
Up to 4
1-4
HP 4 Internal Port SAS HBA with
RAID
Tape and Disk-Based Backup
NOTE: For a complete listing of compatible tape and disk-based
backup offerings, please visit: http://www.hp.com/go/connect NOTE: SAS Tape Drives: Connecting hard drive cage and SAS tape
to the same SAS Controller using split cable (supplied with tape drive)
deactivates 1 of the hard drive bays. Actual hard drive bay deactivated
depends on where split cable plugs into SAS drive connector. Example:
3x SAS cable connector plugged into SAS drive connector (5-8) on the back
of the hard drive cage would mean drive bay 8 is deactivated.
Position
Supported
Controller
Controller Part Number
HP StorageWorks SCSI Tape Drives, External LTO-1 Ultrium 232
LTO-2 Ultrium 448 LTO-3 Ultrium 920 LTO-3 Ultrium 960 LTO-4 Ultrium
1760 LTO-4 Ultrium 1840 DAT 40 DAT 72 DAT 160 1U Rack-Mount
Kit 3U Rack-Mount Kit
HP StorageWorks USB Tape Drives, External DAT 40 USB DAT 72
USB DAT 160 USB 1U USB Rack-Mount Kit
External
USB 2.0 Port
N/A
HP StorageWorks SAS Tape Drives, External DAT 160 SAS LTO-2
Ultrium 448 SAS LTO-3 Ultrium 920 SAS LTO-4 Ultrium 1760 SAS LTO-4
Ultrium 1840 SAS 1U Rack-Mount Kit 3U Rack-Mount Kit
One 6' Highline (IEC-IEC) power cord ships standard NOTE: HP ProLiant DL servers no
longer ship standard with NEMA power cords (163719-002) that allow connection
to 110V US wall outlets in a home or office. HP ProLiant DL servers are
primarily connected to PDU's in data center racks so they now ship standard
with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant
DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001)
must be ordered separately.
If customers require a local power cord, they can check the power cord
matrix for the appropriate cord. Please see the following power cord matrix:
http://www.hp.com/go/powercordmatrix.
- Click on the system of interest. Example: DL165 G5p
- Follow the instructions of the next screens.
Power Supply Output
(per power supply)
Rated Steady-State Power
900 W (at 100 VAC),
1200 W (at 200 VAC)
Maximum Peak Power
900 W (at 100 VAC),
1200 W (at 200 VAC)
System Inlet Temperature
Operating
10° to 35°C (50° to 95°F) at sea level with an altitude
derating of 1.0°C per every 305 m (1.8°F per every 1000 ft) above
sea level to a maximum of 3050 m (10,000 ft), no direct sustained sunlight.
Maximum rate of change is 10°C/hr (18°F/hr). The upper limit may
be limited by the type and number of options installed.
System performance may be reduced if operating with a fan fault or above
30°C (86°F).
Non-operating
-30° to 60°C (-22°
to 140°F). Maximum rate of change is 20°C/hr (36°F/hr).
Relative Humidity
(non-condensing)
Operating
10 to 90% relative humidity (Rh),
28°C (82.4°F) maximum wet bulb temperature, non-condensing.
Non-operating
5 to 95% relative humidity (Rh),
38.7°C (101.7°F) maximum wet bulb temperature, non-condensing.
Altitude
Operating
3050 m (10,000 ft). This value
may be limited by the type and number of options installed. Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
Acoustic Noise
Listed are the declared
A-Weighted sound power levels (LWAd) and declared average bystander position
A-Weighted sound pressure levels (LpAm) when the product is operating in
a 23°C ambient environment. Noise emissions were measured in accordance
with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
Idle
LWAd
6.82 B
LpAm
51.93 dBA
Operating
LWAd
6.84 B
LpAm
51.93 dBA
Emissions Classification
(EMC)
FCC Rating
Class A
Normative Standards
CISPR 22; EN55022; EN55024; FCC
CFR 47, Pt 15; ICES-003; CNS13438; GB9254; K22;K24; EN 61000-3-2; EN 61000-3-3;
EN 60950-1; IEC 60950-1
NOTE:
Product conformance to cited product specifications is based on sample (type)
testing, evaluation, or assessment. This product or family of products is
eligible to bear the appropriate compliance logos and statements.
HP 160GB 1.5G SATA
7.2K NHP 3.5" ETY HDD 458947-B21
160-GB 7.2K
Capacity
160,041 MB
Height
1.028 in (2.61 cm)
Width
4.0 in (10.16 cm)
Depth
5.787 in (147.0 mm)
Interface
Serial ATA
Transfer Rate Synchronous
(Maximum)
1.5Gb/s
Native Command Queuing
N/A
Seek Time
(typical reads, including settling)
Single Track
2.0 ms
Average
<11 ms
Full-Stroke
23.0 ms
Rotational Speed
7,200 rpm
Physical Configuration
Bytes/Sector
512
Logical Blocks
312,581,808
Operating Temperature
41° to 131°
F (5° to 55° C)
Embedded SATA Controller
Drives Supported
Up to 4 SATA devices
Channels
4 1.5Gb SATA
Storage Capacity
3.0TB internal storage
Data Transfer Method
32-bit/33-MHz PCI bus-master
Maximum SATA Channel Transfer
Rate
1.5Gb/s per channel
Maximum Transfer Rate per PCI
Bus (peak)
266 MB/s per channel
Protocols
SATA
PIO Mode[0-4]
Cable
SATA
Internal ATA Connectors
Four SATA connectors
HP 8 Internal Port SAS
HBA with RAID
Drives Supported
Up to 4 SATA/SAS drives
Channels
4
Storage Capacity
1.8TB SAS, 3.0TB SATA
Data Transfer Method
PCI-Express
Maximum SAS Channel Transfer Rate
3Gb/s per channel
Maximum SAS transfer rate
300Mb/sec per port
Protocols Supported
SSP, STP, SMP
Internal Connectors
1 SAS
Embedded NC362i Dual
Port Gigabit Server Adapter
Network Interface
10Base-T/
100Base-TX/
1000Base-TX
Compatibility
IEEE 802.3 10Base-T
IEEE 802.3 1000Base-T
IEEE 802.3 100Base-TX
Data Transfer Method
PCI-X
Network Transfer Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX
(Half and Full-Duplex)
2000 Mb/s
Connector
RJ-45
Cable Support
10Base-T
Categories 3, 4 or 5 UTP; up to
328 ft (100 m)
10/100/1000Base-TX
Category 5 UTP (2 Pair); up to
328 ft (100 m)
Environment-friendly Products and
Approach
End-of-life Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go
to: http://www.hp.com/go/green.
To recycle your product, please go to: http://www.hp.com/go/green
or contact your nearest HP sales office. Products returned to HP will
be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment
information for each product type for use by treatment facilities. This
information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green.
These instructions may be used by recyclers and other WEEE treatment facilities
as well as HP OEM customers who integrate and re-sell HP equipment.
US Site
DL Quickspecs
Search:
497763-B21
© 2012 Canada PartsDirect